Airsoft Press eBook Manual
- Thorough Indepth Review on Airsoft L85 AEG Rifle Upgrades
- Step by Step Illustrated directions and tutorials
- Perfect for Novice or Advanced Airsofters
- Addresses Tokyo Marui, Classic Army, ICS, and other varieties of Airsoft AEG Guns
- A Must have for any player of the Airsoft Sport
- Contains over 110 Pages of Illustrations and Guides
- Click on More Info for Table of Contents
Table of Contents
TOOLS YOU’RE GOING TO NEED
PROPER HANDLING OF THE SCREWS
THE PROPER WAYS OF TAKING THINGS APART AND PUTTING THEM BACK TOGETHER
YOUR UPGRADE OBJECTIVES
UPGRADEABILITY AND PARTS COMPATIBILITY
What is proper AEG usage?
HIGH FPS UPGRADE >
What are the key elements of a high FPS setup?
FPS increase in meter readings VS performance increase in a
practical sense: the law of diminishing marginal gain in
0.20g BBs versus 0.25g BBs versus 0.30g BBs: the heavier the
Does FPS always go hand in hand with Joule?
What is the difference between the FPS system and the Joule
How do you use FPS to measure Joule?
How do you use FPS to give an estimate of the range?
Higher FPS = lower ROF?
Softer spring = Higher ROF?
Harder spring = Lower ROF?
Is 8.4V insufficient for an upgraded mechbox?
Does battery size matter?
Is battery power important for semi-auto firing?
Is EG560 too weak and fragile to power an upgraded mechbox? How
about the Academy Super Black clone?
Why (and why not) should I buy the high torque gear set?
Why (and why not) should I use helical gears?
Why (and why not) should I keep the stock plastic bushings?
Why (and why not) should I replace the stock plastic bushings
with metal bushings?
What is an easy way to (more accurately) shim?
How do I tell if shimming has been done correctly?
What is the recommended order of gear insertion?
Longer spring versus shorter spring: the longer the better?
What are the major parameters of a spring?
Is a harder spring more harmful for the internals?
Installing a long spring: tricks and potential danger.
Installing a short spring: tricks and potential danger.
Why (and why not) should the spring be ground?
How to facilitate spring spinning?
What is a variable pitch spring? Is it always better for AEG?
Use of spacers for spring compression: tricks and potential
What is wrong with a custom made spring?
Systema Springs versus PDI Springs
Can stainless steel spring offer better FPS?
Can Telfon Coated spring offer better FPS?
What can I do to reduce stress on the gears?
Why is it useful to put holes on the piston head? Any
Why (and why not) should I use a metallic piston head?
How about a silent head set?
Is aluminum piston more durable?
How do I effectively reduce heat on the motor?
Why (and why not) is the one o’clock gear timing an issue?
Can I still use the smaller batteries to power my upgraded
I want to hide my battery inside the grip but the battery cells
are too big. What should I do?
Chaining up your batteries: Parallel VS Serial configurations.
Should I use Sanyo battery cells for maximum performance?
How safe is it to remove the fuse? Any alternative?
Why (and why not) is it necessary to replace the stock wires?
Why is it necessary to shorten the wires?
Can I use stereo wires instead?
Why (and why not) is it necessary to replace the stock Tamiya
Are NiCd batteries superior to NiMH batteries for driving
How do I optimize the overall performance of the stock motor?
Is it possible to increase the torque of the stock motor? If so,
What else should I buy for a high FPS configuration?
What is wrong with the soda can test?
What is right with the soda can test?
What is the most accurate way to measure FPS?
HIGH ROF UPGRADE
What are the key elements of a high ROF setup?
Can I increase the ROF while keeping the FPS at the stock level
by using 9.6V battery?
Voltage VS mah – which one matters the most?
Can I increase the ROF by replacing the mechanical contact
switch with a solid state switching mechanism based on MOSFET?
Can I increase the ROF by using capacitors at the power source?
Is high ROF a major cause of tappet plate breakage?
ROF-wise, why (and why not) should I replace the stock plastic
bushings with ball bearings?
ROF-wise, why (and why not) should I replace the stock plastic
bushings with metal bushings?
How about oil channel bushings?
Why (and why not) should I buy the high speed gear set?
Should I upgrade to a Teflon Cylinder?
How about a high speed cylinder set?
What makes a ball bearing spring guide meaningless for a TM
piston set? How to work around?
Is there any alternative to ball bearing spring guide?
Why a ball bearing spring guide alone may not increase the ROF?
How do I optimize the stock motor’s RPM without spending major
How can I increase the ROF while keeping the FPS at
What is the right type of spring and battery to use for this
Is ROF over 30/sec possible?
What is the major ROF bottleneck?
Is aluminum piston better off for a high ROF configuration?
Are lighter gears better off for a high ROF configuration?
What else should I buy for a high ROF configuration?
Can I increase ROF by cutting off some teeth from the piston and
HIGH ACCURACY UPGRADE
What are the key elements of a high accuracy setup?
Can a long barrel deliver higher accuracy and range?
What is good about a high precision barrel?
How to maximize the effectiveness of a high precision barrel?
My stock L85A1 is dead after 3000 shots. Why?
What will happen with improper shimming?
And what should I do to remedy the problem?
How do I prolong the life of the mechbox?
When the mechbox is running, the nozzle does not move at all.
What is wrong?
My gun stopped working in semi-auto mode. What’s wrong?
What cause the piston gear to break prematurely?
My motor was overheated. What should I do?
What should I do for proper motor maintenance?
What causes gear stripping?
What can cause the hopup rubber to break?
How to prolong the life of my battery?
Is slow charging always good for my battery?
How to safely charge a battery?
Is NiMH battery free from the memory effect problem?
Should I fully discharge the battery every time after use?
How do I fix the battery memory effect problem?
My gun keeps mis-firing. How do I tell if this is a magazine
problem or a mechbox problem?
I suspect that the hi-cap magazine is not working. What should I
do to fix it?
What causes double feeding?
My gun makes an unwinding noise after full auto firing. What’s
What causes air leakage?
What needs to be regularly replaced to keep my gun in good
Free Sample of Airsoft Press AEG V2 Mechbox Upgrade Manual and AEG V3 Mechbox Upgrade Manual
| Best Industry Return / Warranty Policy |